The distance between the two dowels on the SnowBear 5Xm5 Universal Cross Member # SB324-060 is approximately 32-3/4 inches. The diameter of the dowels themselves is 1-5/8 inches and they are just about 4 inches in height.
This cross member is designed for SnowBear Plows and will install between the 2-point vehicle specific mounting brackets and the snow plow itself. view full answer...
Your hitch's maximum tow weight rating can sometimes be imprinted into the steel somewhere on the crossbeam. You may need to clean it up really good and feel around for it on that old of a hitch. Based off the information you have given me I was able to go through our system and see what options we have available for your 1999 Chevrolet S-10 Pickup. All of the 2" receiver hitches we have, like the Curt Trailer Hitch Receiver item # C13315 you were looking at, are class III hitches. All... view full answer...
I went out to the warehouse to take that measurement on the MaxxTow Tow Hook # MT70028 for you. From the center of the pin hole to plate where the hook starts to come out is 4-1/8 inches. To the back of that plate it is approximately 1/4 inch less so 3-5/8 inches. view full answer...
I checked with Extang and the replacement cover you need is the Replacement Tarp for Extang BlackMax Soft Tonneau Cover item # EX1560. This is the tarp that comes with the Extang BlackMax Soft Tonneau Cover EX2560 that fits the 83-93 Chevy S-10's. view full answer...
I pulled a LED Step/Area Light # ILL85CB from our warehouse to measure the wire that comes from the assembly and found that the portion that has the black cover over the wires measures 41 inches and the exposed white and black wires measure an additional 5 inches.
I shot a video of me measuring the wire for you to check out also. view full answer...
Thanks for the picture! For your 2002 Chevy S-10 Extreme, you will want the Curt Trailer Hitch item # 13920. This hitch is custom fit and bolts to your S-10 with included hardware. Since your truck has the factory roll pan bumper this will mount the hitch behind your license plate.
The Curt Trailer Hitch item # 13920 is a class III hitch with a 2" receiver. It has a 3,500 lbs towing capacity, and a 350 lbs maximum tongue weight. This hitch is made in the USA and weighs 27 lbs.
If you... view full answer...
Some weight can be put on top of the Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover with Explorer Series Rails # 311-FEC0202.
The cover has a capacity of 300 lbs evenly distributed over the cover, which means that it will handle the weight of a heavy snowfall, for example. It isn't really designed to be stood on or have weight put on it consistently, which you'll want to keep in mind.
The Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover with Explorer... view full answer...
Unfortunately, we do not have a product by itself to relocate the sewer dump. However, you might be able raise the level of your trailer to gain more ground clearance.
Installing an Over-Under Conversion Kit, # K71-384-00 or # K71-385-00, can give you more ground clearance under your trailer. The kits will work if your trailer axles have the leaf springs located on the bottom of the axle.
These kits come in two sizes, the # K71-384-000 will fit a 2-3/8 inch axle tube and the # K71-385-000... view full answer...
You can see the various hitches available for your vehicle by clicking on the provided link. Use the drop down menu to choose the bumper style of your S-10.
The Class II hitch for a 1997 S-10 has a 3500 lb towing/300 lb tongue weight capacity, while the Class III has a 3500 lb towing/350 lb tongue weight capacity. You can certainly change to a Class III if you wish, but you will only realize a 50 lb increase in tongue weight.
I would recommend you determine the fully loaded and ready... view full answer...
Go To Results